Hot Rolled Stainless Steel Coil

Thickness: 2.8-16.0mm
Width: 1240-1500mm
Surface: No.1 to Brushed/8K (3.0-4.0mm)
Average Delivery Time: 10-15 Days

For the No.1 stainless steel coil, the origin is very important. Basically, You can classify the origin into private mills and governmental mills.

For No.1, TISCO BAOSTEEL ZPSS is always the best mill with the best guarantee and service

however, some private mills also start to compete with governmental mills, which are much cheaper than the governmental mills, like donate, Qingshan.

Property of No.1 Stainless Steel Coil

Chemical Composition % By Mass Max Unless Stated
AISI No / Common Name	C	Si	Mn	P	S	Cr	Mo	Ni	Others
301	0.15	1	2	0.045	0.03	16.0/18.0	–	6.0/8.0	N 0.10
301L	0.03	1	2	0.045	0.03	16.0/18.0	–	6.0/8.0	N 0.20
301LN	0.03	1	2	0.045	0.03	16.0/18.0	–	6.0/8.0	N 0.07/0.20
302	0.15	0.75	2	0.045	0.03	17.0/19.0	–	8.0/10.0	N 0.10
30No.1	0.15	2.00/3.00	2	0.045	0.03	17.0/19.0	–	8.0/10.0	–
303	0.15	1	2	0.2	0.15 min	17.0/19.0	–	8.0/10.0
XM-5 (303Plus x)	0.15	1	2.50/4.50	0.2	0.25 min	17.00/19.00	–	7.00/9.00	–
303Se	0.15	1	2	0.2	0.06	17.0/19.0	–	8.0/10.0	Se 0.15 min
303Cu	0.15	1	2	0.15	0.10 min	17.0/19.0	–	6.0/10.0	Cu 2.5/4.0; Se 0.10
304	0.07	0.75	2	0.045	0.03	17.5/19.5	–	8.0/10.5	N 0.10
304	0.08	1	2	0.045	0.03	18.0/20.0		8.0/11.0
304L	0.03	0.75	2	0.045	0.03	17.5/19.5	–	8.0/12.0	N 0.10
302HQ	0.03	1	2	0.045	0.03	17.0/19.0	–	8.0/10.0	Cu 3.0/4.0
XM-21 (304HN)	0.08	1	2	0.045	0.03	18.0/20.0	–	8.00/10.00	N 0.16/0.30
304LN	0.03	0.75	2	0.045	0.03	18.0/20.0	–	8.0/12.0	N 0.10/0.16
305	0.12	0.75	2	0.045	0.03	17.0/19.0	–	10.5/13.0	–
308	0.08	1	2	0.045	0.03	19.0/21.0	–	10.0/12.0	–
316	0.08	0.75	2	0.045	0.03	16.0/18.0	2.00/3.00	10.0/14.0	N 0.10
316L	0.03	0.75	2	0.045	0.03	16.0/18.0	2.00/3.00	10.0/14.0	N 0.10
316Ti	0.08	0.75	2	0.045	0.03	16.0/18.0	2.00/3.00	10.0/14.0
316Cb	0.08	0.75	2	0.045	0.03	16.0/18.0	2.00/3.00	10.0/14.0
316LN	0.03	0.75	2	0.045	0.03	16.0/18.0	2.00/3.00	10.0/14.0	N 0.10/0.16
317	0.08	0.75	2	0.045	0.03	18.0/20.0	3.0/4.0	11.0/15.0	N 0.10
317L	0.03	0.75	2	0.045	0.03	18.0/20.0	3.00/4.00	11.0/15.0	N 0.10
317LM	0.03	0.75	2	0.045	0.03	18.0/20.0	4.0/5.0	13.5/17.5	N 0.20
317LMN	0.03	0.75	2	0.045	0.03	17.0/20.0	4.0/5.0	13.5/17.5	N 0.10/0.20
317LN	0.03	0.75	2	0.045	0.03	18.0/20.0	3.0/4.0	11.0/15.0	N 0.10/0.22
321	0.08	0.75	2	0.045	0.03	17.0/19.0	–	9.0/12.0
347	0.08	0.75	2	0.045	0.03	17.0/19.0	–	9.0/13.0	Nb+Ta 10 x C min/1.0
347F	0.08	1	2	0.04	0.18/0.35	17.00/19.00	0.75	9.00/12.00	Nb 10xC / 1.10; Cu 0.75; Ta 0.05
347FSe	0.08	1	2	0.11/0.17	0.03	17.00/19.00	0.75	9.00/12.00	Nb 10xC / 1.10; Cu 0.75; Se 0.15/0.35; Ta 0.05
348	0.08	0.75	2	0.045	0.03	17.0/19.0	–	9.00/13.0	Nb+Ta 10 x C / 1.00; Ta:0.10 max; Co 0.20
384	0.04	1	2	0.045	0.03	15.0/17.0	–	17.0/19.0	–