Nickel, molybdenum, chromium, and other elements compose the alloy C-2000 Hastelloy, with a nickel content of about 55%.
It can withstand a wide range of oxidizing and nonoxidizing chemicals. It also has excellent resistance to pitting and crevice corrosion in chlorides and other halides.
Alloy C-2000 alloy has been listed in ASME and ASTM standards B-564, B-574, B575, B619, B-622, and B-366.
The DIN standard No. is 2.4675, and the UNS No. is N06200. The density of C2000 is small, about 8.5g/cm3.
The combined action of molybdenum and copper (at the level of 16% and 1.6% respectively) makes the alloy the ability to resist the corrosion of reducing media. And the high chromium content (23% wt) ensures resistance to the corrosion of oxidizing media.
applications of alloy c-2000
1. Aerospace
2. Environmental Protection Equipment
3. Kitchen Equipment
4. Food Machinery
5. Construction Engineering
6. Chemical Equipment
7. Shipbuilding
8. Pharmaceutical Equipment
| Material | Alloy C-2000 |
| Shape | Round, Forging, Ring, Coil, Flange, Disc, Foil, Spherical, Ribbon, Square, Bar, Pipe, Sheet |
| Specification | Wire: 0.01-10mm Strip: 0.05*5.0-5.0*250mm Bar: φ4-50mm; Length 2000-5000mm Pipe: φ6-273mm;δ1-30mm;Length 1000-8000mm Sheet: δ 0.8-36mm; Width 650-2000mm; Length 800-4500mm |
| Application | High-temperature components such as turbine blades, guide vanes, turbine disks, high-pressure compressor disks, machine manufacturing and combustion chambers used in the manufacture of aviation, naval, and industrial gas turbines |
| Alloy C-2000 Chemical Composition | |
| C | 0.010 max |
| Mn | 0.50 max |
| Si | 0.08 max |
| P | 0.025 max |
| S | 0.010 max |
| Cr | 22.0 – 24.0 |
| Co | 2.0 max |
| Mo | 15.0 – 17.0 |
| V | 0.50 max |
| Fe | 3.0 max |
| Al | 0.50 max |
| Cu | 1.30 – 1.90 |
| Ni | Balance |
PVC film is one of the most important factor when purchasing stainless steel material. Basically, 3 types of PVC films are typically applied.
PE50/PE80 black and white film
This is the most widely used film, the thickness normally ranges from 50 micron to 80 microns. There will not be any special function except protection.,
Laser Film(Novacel 4228)
Laser cutting is often applied as a downstream processing. Laser film is a film that can undertake high temperature. If clients apply the wrong pvc, after laser cutting, the pvc will be wrinkled and sticky to the surface.
Transparent Film
There are normally 2 types of blue transparent film, one is the for deep drawing, another one is normal protection film.
Stainless Steel sheet/Plates Packing and Loading Solution
Film Attaching
The edge part should be clean and slit, no residues left.
Back side kraft paper
To make sure there is less moisture going into the pallet, water proof kraft paper should be applied.
Standard sheet package
A layer of wooden plate will be put on the top of the pallet. And 3*2 steel strip will be applied.
Block and bundles
Wooden blocks and bundles will apply on the loading of the pallets.
Top locating
If there are too many pallet in one column，the top part also need be strengthened.
Wooden box package
For stainless steel mirror sheet, we can also apply wooden box.
01
Thickness Tolerance
Normally, different mills will apply 3 types tolerance, like 1.0mm, there will be 0.91-0.92mm/0.94-0.96mm/ 0.98-1.01mm. 3 stages to apply for different application.
02
Width Tolerance
Width tolerance mainly depends on the slitting and cutting machine. We use Taiwan and Italy machinery, which can guarantee +/-0.05 to +/-0.1mm
03
Diagonal Tolerance
Diagonal Tolerance is a key factor to show whether the cut is correct or not. The normal tolerance is +/-2mm。
